ISA Setup to allow a port

Hi,
I need to setup ISA to allow a particular IP address with ports 0 to 5 and
am having problems.
Tried to Telnet IP port 0 and it failed. Can anyone assist me with the
setup of ISA.

Regards
David Hellewell

David
Thu Apr 29 17:19:04 CDT 2004

Hi,
I have just found out the following so any assistance would be appreciated.

CAS connects to ASIC's Internet lodgement system via the following
addresses:

edge1.asic.gov.au - primary mailbox (IP address 203.53.43.10)
edge2.asic.gov.au - secondary mailbox (IP address 203.202.5.10)

CAS will connect to whichever Mailbox is specified in the Agent Setup
screen, where either "Primary Mailbox" or "Secondary Mailbox" can be
specified.

The connection that CAS uses for these Mailboxes is a TCP connection to the
remote port 5610 to the IP addresses listed above.

The local TCP port used for the connection can be specified in the Agent
setup screen if required. By default this is 0. If CAS is unable to
establish a remote connection using the port specified, it increments the
port number by one and tries again- this is repeated five times before CAS
reports that it is unable to connect. So, for example if the default port 0
is used, CAS will try port 0, then ports 1-5 in sequence before it reports a
failed connection.

Regards
David Hellewell
"David Hellewell" <nospam@bigbwana.com.au> wrote in message
news:OBekc.407$2u4.10205@nnrp1.ozemail.com.au...
> Hi,
> I need to setup ISA to allow a particular IP address with ports 0 to 5 and
> am having problems.
> Tried to Telnet IP port 0 and it failed. Can anyone assist me with the
> setup of ISA.
>
> Regards
> David Hellewell
>
>

Chad
Thu Apr 29 17:21:05 CDT 2004

Hi David -

Inbound or Outbound access? If inbound, is it a service on the server that
you need to connect to, or a service/app on a workstation / member server?
If outbound, does the server or the workstations need access?

--

Chad A. Gross - SBS MVP
SBS ROCKS!

www.msmvps.com/cgross
www.gosbs.org


David Hellewell wrote:
> Hi,
> I need to setup ISA to allow a particular IP address with ports 0 to
> 5 and am having problems.
> Tried to Telnet IP port 0 and it failed. Can anyone assist me with
> the setup of ISA.
>
> Regards
> David Hellewell

David
Thu Apr 29 18:02:06 CDT 2004

Hi Chad,
Problem solved, I had to create both Inbound and Outbound. Thanks

--
Regards
David Hellewell
"Chad A. Gross [SBS MVP]" <chad.gross@laytonflower.nospam.com> wrote in
message news:%23BAnEhjLEHA.3064@TK2MSFTNGP11.phx.gbl...
> Hi David -
>
> Inbound or Outbound access? If inbound, is it a service on the server
that
> you need to connect to, or a service/app on a workstation / member server?
> If outbound, does the server or the workstations need access?
>
> --
>
> Chad A. Gross - SBS MVP
> SBS ROCKS!
>
> www.msmvps.com/cgross
> www.gosbs.org
>
>
> David Hellewell wrote:
> > Hi,
> > I need to setup ISA to allow a particular IP address with ports 0 to
> > 5 and am having problems.
> > Tried to Telnet IP port 0 and it failed. Can anyone assist me with
> > the setup of ISA.
> >
> > Regards
> > David Hellewell
>
>